[Solved] SOLVED:Computer Assignment 3

Assignment Overview In this assignment you will use Vivado 15.2 Webpack to write, simulate and program an FPGA. Youll use the encoder.vhd created in the last CAD and connect it up to switches and the seven segment displays on the FPGA board. Youll also need to turn in a single PDF to Moodle (instructions below).Background This assignment is pretty simple. You need to declare your encoder.vhd component, then instantiate it 4 times, and connect all of the signals. I find it useful to tie the switches to the LEDs to make it easier to read what the seven segment display should read.Structural VHDL is simple. You have to declare a component before you instantiate it. Once you instantiate it, you simply connect signals to it. Sort of like working with a schematic but with text. The VHDL slides offer information on structural syntax. If you want toDrivers for the FPGA Board The FPGA board requires some drivers for it to be recognized by Vivado. You need to download and install Digilents Adept System software which can be located at https://www.digilentinc.com/Products/Detail.cfm?NavPath=2,66,828&Prod=ADEPT2Getting started 1. Create a directory to store all of the assignments files. 2. Open Vivado 2015.2 and create a new project called computer_assignment_3. 3. It will be an RTL project 4. Add your encoder.vhd file from CAD 2 and the supplied ssd_muxer.vhd file for Dr Conrads website. 5. No existing IP. 6. Add the constraints/xdc file. a) DL https://www.digilentinc.com/Data/Products/BASYS3/basys3_master.zip . b) Extract the zip file. c) Add the extracted file as a constraints/xdc file. 7. The Basis3 uses an XC7A35TCPG236C-1 FPGA Artix 35T Speed grade -1 CPG236 packaging C temp grade

Figure 1: Overview of the CADTask This task is to implement an encoder which input is a 1 4-bit hex signal and the output is 7 1-bit signals for each display segment (A-G). 1. Edit the constraints file and uncomment the lines corresponding with: sw clk seg dp an led 2. Create the top.vhd file: a) Under Flow Navigator click Add sources. b) Select Create or add design sources. c) Create top.vhd and then click Finish. d) Create inputs: sw ~ (15 downto 0) clk e) Create outputs: seg ~ (6 downto 0) dp an ~ (3 downto 0) led ~ (15 downto 0) 3. Once you have your vhdl source file (top.vhd), edit it to implement 4 encoder entities and connect the switches to the LEDs. Since you already have the encoder.vhd, youll just be using structural VHDL to connect multiple encoder entities to the sdd_muxer entity. If youre feeling adventurous you can use a for generator statement or you can manually place four encoder entities. 4. Make sure its syntax error free and can be synthesized. 5. Add the top_tb.vhd file: a) Under Flow Navigator click Add sources. b) Select Create or add simulation sources. c) Add top_tb.vhd. d) Make sure simulation set is sim_1. e) Click Finish. 6. Edit ssd_muxer.vhd: a) Go to line 57-58, there will be two counter_max constants. b) Make sure the one that says fpga is commented out and the one that says sim is uncommented. 7. Select the right simulation set: a) Under Flow Navigator click Simulation Settings. b) Under Simulation set input sim_1. c) Under Simulation top module name input top_tb. d) Click Ok. 8. Run the simulation by and check your results. The expected output is on the last page of the assignment. 9. Once youve simulated the circuit correctly, you need to edit ssd_muxer.vhd again.a) Go to line 57-58, there will be two counter_max constants b) Make sure the one that says fpga is uncommented out and the one that says sim is commented. 10. Create the file you need to load onto the FPGA (the bitstream). Click Generate Bitstream under the Flow Navigator. 11. Program the FPGAG board a) Hardware Manager in the Flow Navigator. b) Open Target and then Auto Connect. c) Program Device and then xc7a35t_0. d) The defaults of the pop up are ok, just press program.Figure 2: Expected Waveform of SimulationTurn in The write up is very simple, just include things like: the basic design process, anything you had trouble with, an explanation of anything that doesnt work, etc. It isnt meant to be extensive, but a brief overview.Make sure everything is in a single PDF on Moodle. You can join PDFs with Adobe Acrobat if you have multiple PDFs. Name the assignment CAD3-xxxxxx-yyyyyy, where xxxxxx is the last name of one lab partner and yyyyyy is the last name of the other lab partner. Turn in only one pdf under one of the lab partners Moodle account.Make sure everything is in a single PDF on moodle.Grading Write up /4 Points Printout and correctness of code (top.vhd and encoder.vhd) /6 Points Demonstration of FPGA /10 Points /Total of 20 Points Demonstration The demonstration of the code is simple. Brian will be the TA you need to demonstrate the VHDL running on the FPGA. All that is needed is to go through some cycles of each set of 4 switches and show that the correct output is displayed on the seven segment displays. Print off the demonstration page (see the website) when you go to demo the code on the FPGA.Demonstration Grading: Each seven segment display works correctly /2 points x 4 The switches are tied to the LEDs. /2 points /Total of 10 points

NO WRITE UP