[SOLVED] :csc258 – lab 2 multiplexers, design hierarchy, and hex displays

The purpose of this lab exercise is to use gates to build simple circuits, and to learn the importance of
simulations and hierarchies. This exercise is also meant to illustrate the importance of Karnaugh maps in
designing circuits, and introduce important devices such as the multiplexer and seven-segment decoder.This lab also introduces components of the DE1-SoC board and FPGA design in general. The DE1-SOC
board is the hardware used in the physical labs to which we upload circuit designs. For this lab we will
simulate the use of switches SW9−0 on the DE1-SoC board as inputs to the circuit, and Light Emitting
Diodes (LEDs) and 7-segment displays as output devices.This lab is also meant to introduce new notation and terminology when we mimic physical hardware.
For instance, we may refer to signals on the input switches on the DE1-SoC as SW9−0, i.e., with the
subscripts. In place of these physical switches, we will approximate these inputs and outputs in Logisim
instead.
*** Note that we will not be using the actual DE1-SOC board in Winter 2021.2 Resources
You can find many resources about the DE1-SoC board here http://cd-DE1-soc.terasic.com/. The
User Manual for the DE1-SoC board can be downloaded from here: http://www-ug.eecg.toronto.
edu/desl/manuals/DE1-SoC_User_manual.pdf3 Marking Scheme
This lab is worth 6% of your final grade, but you will be graded out of 8 marks for this lab, as follows:
• Prelab + Testing: 3 marks
• Part I (in-lab): 1 mark
• Part II (in-lab): 2 marks
• Part III (in-lab): 2 marks4 Preparation Before the Lab
For this lab and all future labs, your prelab report should include schematics (which can either be drawn
by hand on paper or in Logisim), and simulations of your circuits (like the test vector file in Lab 1 and
the test result).The schematics should show the structure of your circuit, much like the schematics in Lab 1 showed
how your circuit should be built. Figure 1 and Figure 3 are examples of how to draw the schematic for
multiplexers. For the schematics you will need to show the names of each input and output (in your
Logisim circuits) and the switches or LEDs to which they would be mapped on the DE1-SoC board (for
the top-level module).Your circuit design in Logisim will consist of a number of modules, where a module is like the circuitry
equivalent of a class in Java or Python, encapsulating and implementing a circuit instead of code. Think
of modules as logic functions consisting of multiple gates, such as the logic functions in Lab 1.Modules can contain other modules. The top-level module would be the one that is uploaded to the
DE1-SOC board. In addition to showing how its component modules are wired together, the top-level
module would also have inputs and outputs that correspond to signals on the DE1-SOC board, i.e.,
connections to switches, LEDs, 7-segment hex displays, etc. The port names of all modules, wires and
I/O ports should be clearly labeled in your schematics.For your simulations, you should have a test vector file or files, that tests important aspects of your
design. Print out the test result on Logisim and include that into your prelab report (e.g. by taking a
screenshot).If the simulation is very long, make sure to print out the salient parts to demonstrate that the key
elements of your circuit are working and that you have done the simulations. It is not necessary to have
pages and pages of results. However, occasionally, you will be asked to demonstrate and explain any
part of simulation to the TA in the lab, so be prepared for this.As an example, if your circuit implements a logic function with three or four inputs, it is reasonable to
show waveforms demonstrating the functionality of all possible combinations of input values. However,
if your circuit implements a logic function with ten inputs, it would be unreasonable to simulate all 210
possible input values. Instead, use similar approaches to testing that you would use for software; find
groups of inputs that are logically related and test each group independently.For instance, if you have a
multiplexer module and an adder module, it is reasonable to assume that you can test each independently
instead of testing all combinations of all their inputs combined.5 Part I
This part of the lab expands slightly on the mux circuit from Lab 1, introducing the concept of creating a
module and associating the input and outputs to the physical hardware of the physical DE1-SOC board.
Logisim File (.circ)The DE1-SoC board in the on-campus labs provide 10 toggle switches, called SW9−0 that can be used
as inputs to a circuit, and 10 red lights, called LEDR9−0, that can be set high or low to display output
values. These subscript ranges indicate the names of the individual inputs and outputs. For instance,
your circuit could take signal SW[0] as an input and send a result to LEDR[0] and LEDR[1]. As far as
your Logisim design is concerned, we will use the same input and output pins from the tool bar that you
used in Lab 1.If we were using the DE1-SOC boards in the on-campus lab rooms, we would need to map the inputs
and outputs for the top-level Logisim module to the SW9−0 and LEDR9−0 pins on the DE1-SOC board
respectively before uploading your design to the board.Unfortunately, at this point we do not have
access to the boards in the on-campus labs, but we will still use the DE1-SOC ideas and terminology
to approximate the way your design would map to the physical board. A Logisim file for a 2-to-1
multiplexer, named mux.circ, has already been provided to you on Quercus.After you open this mux file in Logisim, the main is a very trivial example of a design hierarchy, as it
only instantiates a single mux2to1 module. In the more general case, a single module can instantiate a
number of interconnected modules. However, in any circuit you build, there must be only one top-level
module (called main in Logisim).The names of the left side of the rectangular module symbol match
the input ports of the mux2to1 module and on the right side, it is the output port of the mux2to1
module. Note that you can have multiple modules of the same type in a single circuit, similar to how
several objects of the same type can be used together in the implementation of a larger object.And
similar to object-oriented programming, each use of a module is called an instance and every instance
in a single circuit must have a unique label. In our example below we used only one instance of the
mux2to1 module, which we named u. There are two modules, main and mux2to1 in mux.circ, you can
check this in Components. Double-clicking on either of them to view the module on canvas:
Currently main has 3 inputs, corresponding to the three multiplexer inputs.The input labeled x on
the multiplexer would be connected to an input called SW0 in Logisim (which maps this to SW[0] on
DE1-SOC); the input labeled y on the multiplexer would be connected to the input SW1 in Logisim
(which maps to SW[1] on DE1-SOC) and the input signal labeled s would be connected to the input
SW9 in Logisim (map this to SW[9] on DE1-SOC).The output is the output LEDR0 in Logisim, which
would map to the LEDR0 on the DE1-SOC board.
Figure 1 shows the symbol for a 2-to-1 multiplexer. As mentioned in Lab 1, a multiplexer is a device
that uses a select signal to select which one of multiple inputs should appear on the output of the device.In Figure 1, input s will control which of the inputs x and y will appear on the output m. If s is 0, x
will appear on the output, while if s is 1, y will appear on the output.
Figure 1: Symbol for a 2-to-1 multiplexerThe Boolean expression for a 2-to-1 multiplexer is m = xs’+ ys.
Test Vector File (.txt)
After building the circuit in Logisim, and to verify the circuit’s functionality properly, we can perform
testing using a test vector file like in Lab1. This file is also provided to you (on Quercus).This test file includes the truth table for the 2to1 mux. And you should be able to run the tests through
Simulate > Test Vector…
# Tes t Vec tor f o r mux2to1
SW 0 SW 1 SW 9 LEDR 0
0 0 0 0
0 1 0 0
1 0 0 1
1 1 0 1
0 0 1 0
0 1 1 1
1 0 1 0
1 1 1 16 Part II
Start with the design given in Part I and modify the design to make it a 4-to-1 multiplexer. You must
use multiple instantiations of the mux2to1 module given to you in Part I. This is known as hierarchical
design and is a good practice especially for larger designs where the circuits you build can become more
difficult to debug. Smaller submodules are generally easier to test thoroughly and debug.Create a new circuit by clicking on the green plus sign just above the components. Enter ”mux4to1” for
”Circuit Name”. Then, simply click on the mux2to1 module and drop it on the canvas. You can then
connect the input and output of the instantiated model with input and output of your current module
with wires. Note: All inputs and outputs of the module have to be the default type from the
tool bar. But you can do some experiments yourselves to see what could happen when we instantiate
a module with other types of input output in Input/Output.Figure 2 shows a schematic of two modules connected with wires.
Figure 2: Using wires to make a connection between two modules
Now construct a module for the 4-to-1 multiplexer shown in Figure 3 with the truth table shown in Table
using wires and multiple instances of the mux2to1 module.Note that the truth table in Table 1 is given
in a short-hand form. A real truth table would consist of rows enumerating all possible combinations of
values of inputs u, v, w, x, in addition to s0 and s1, and show the value (0 or 1) of the output m for each
row of the truth table. Since this would result in a truth table with a large number of rows, it is written
in short-hand form instead.Figure 3: Symbol for a 4-to-1 multiplexer
s1s0 m
00 u
01 v
10 w
11 x
Table 1: Truth table for a 4-to-1 multiplexerPerform the following steps:
1. Answer the following question: if the truth table in Table 1 was given in full, how many rows would
it have? (PRELAB)2. Draw a schematic (not in Logisim) showing how you will connect the mux2to1 modules to build
the 4-to-1 multiplexer. Be prepared to explain it to the TA as part of your prelab. The schematic
should reflect how you are going to create your Logisim circuit. (PRELAB)3. Build your circuit in Logisim (PRELAB)
4. Test your circuit with different values of s, u, v, w and x. Do enough testing to convince yourself
that the circuit is working. You must show these to the TA as part of your prelab. (PRELAB)
Answers to questions and hand-drawn schematics should be included in your prelab report and submitted
online before the lab7 Part III
In this part of the lab, you will design a decoder for the 7-segment HEX display as shown in Figure 4.
The output of the HEX display is determined by the value at the input of the decoder as shown in
Table 2. We call this a HEX display because it can display all hexadecimal digits.When you build your circuit in Logisim, use default inputs and 7-Segment Display as output.
HINT: In order to solve this part you need to first identify which segment needs to be illuminated for
every input and then write a Boolean function for each one of the seven segments of the HEX display so
they are turned on when needed. You must use Karnaugh maps to optimize those Boolean expressions
before you build the corresponding circuits in Logisim.Figure 4: HEX decoder
c3c2c1c0 Character
0000 0
0001 1
0010 2
0011 3
0100 4
0101 5
0110 6
0111 7
1000 8
1001 9
1010 A
1011 b
1100 C
1101 d
1110 E
1111 F
Table 2: Desired behaviour of HEX decoderPerform the following steps:
1. Write the expressions for seven Boolean functions, one for each segment of the 7-segment decoder.
You must use Karnaugh maps for optimization. You should be able to explain to the TA how you
generated these expressions by showing them the truth-tables you wrote, and Karnaugh maps you
used to optimize your circuits. (PRELAB)2. Build the circuit for the 7-segment decoder in Logisim taking advantage of the aforementioned
expressions. HINT: you can change the number of inputs for each gate by selecting it and go to
Properties. Also it might be helpful to separate the circuits for each of the 7 segments into different
modules. (PRELAB)3. Check whether your implementation is correct. To verify the correctness of each segment, you need
to create a test vector file for each segment’s truth table. To test whether your circuits for each
segment connect well with the 7-Segment Display in Logisim, use ’Poke’ on the tool bar. Show the
screenshots of your simulation to your TA as part of the prelab. (PRELAB)