[SOLVED] CS flex #include devices/ide.h

#include devices/ide.h
#include
#include
#include
#include
#include devices/block.h
#include devices/partition.h
#include devices/timer.h
#include threads/io.h
#include threads/interrupt.h
#include threads/lock.h

/* The code in this file is an interface to an ATA (IDE)
controller.It attempts to comply to [ATA-3]. */

/* ATA command block port addresses. */
#define reg_data(CHANNEL) ((CHANNEL)->reg_base + 0) /* Data. */
#define reg_error(CHANNEL) ((CHANNEL)->reg_base + 1)/* Error. */
#define reg_nsect(CHANNEL) ((CHANNEL)->reg_base + 2)/* Sector Count. */
#define reg_lbal(CHANNEL) ((CHANNEL)->reg_base + 3) /* LBA 0:7. */
#define reg_lbam(CHANNEL) ((CHANNEL)->reg_base + 4) /* LBA 15:8. */
#define reg_lbah(CHANNEL) ((CHANNEL)->reg_base + 5) /* LBA 23:16. */
#define reg_device(CHANNEL) ((CHANNEL)->reg_base + 6) /* Device/LBA 27:24. */
#define reg_status(CHANNEL) ((CHANNEL)->reg_base + 7) /* Status (r/o). */
#define reg_command(CHANNEL) reg_status (CHANNEL) /* Command (w/o). */

/* ATA control block port addresses.
(If we supported non-legacy ATA controllers this would not be
flexible enough, but its fine for what we do.) */
#define reg_ctl(CHANNEL) ((CHANNEL)->reg_base + 0x206)/* Control (w/o). */
#define reg_alt_status(CHANNEL) reg_ctl (CHANNEL) /* Alt Status (r/o). */

/* Alternate Status Register bits. */
#define STA_BSY 0x80/* Busy. */
#define STA_DRDY 0x40 /* Device Ready. */
#define STA_DRQ 0x08/* Data Request. */

/* Control Register bits. */
#define CTL_SRST 0x04 /* Software Reset. */

/* Device Register bits. */
#define DEV_MBS 0xa0/* Must be set. */
#define DEV_LBA 0x40/* Linear based addressing. */
#define DEV_DEV 0x10/* Select device: 0=master, 1=slave. */

/* Commands.
Many more are defined but this is the small subset that we
use. */
#define CMD_IDENTIFY_DEVICE 0xec/* IDENTIFY DEVICE. */
#define CMD_READ_SECTOR_RETRY 0x20/* READ SECTOR with retries. */
#define CMD_WRITE_SECTOR_RETRY 0x30 /* WRITE SECTOR with retries. */

/* An ATA device. */
struct ata_disk
{
char name[8]; /* Name, e.g. hda. */
struct channel *channel;/* Channel that disk is attached to. */
int dev_no; /* Device 0 or 1 for master or slave. */
bool is_ata;/* Is device an ATA disk? */
};

/* An ATA channel (aka controller).
Each channel can control up to two disks. */
struct channel
{
char name[8]; /* Name, e.g. ide0. */
uint16_t reg_base;/* Base I/O port. */
uint8_t irq;/* Interrupt in use. */

struct lock lock; /* Must acquire to access the controller. */
bool expecting_interrupt; /* True if an interrupt is expected, false if
any interrupt would be spurious. */
struct semaphore completion_wait; /* Upd by interrupt handler. */

struct ata_disk devices[2]; /* The devices on this channel. */
};

/* We support the two legacy ATA channels found in a standard PC. */
#define CHANNEL_CNT 2
static struct channel channels[CHANNEL_CNT];

static struct block_operations ide_operations;

static void reset_channel (struct channel *);
static bool check_device_type (struct ata_disk *);
static void identify_ata_device (struct ata_disk *);

static void select_sector (struct ata_disk *, block_sector_t);
static void issue_pio_command (struct channel *, uint8_t command);
static void input_sector (struct channel *, void *);
static void output_sector (struct channel *, const void *);

static void wait_until_idle (const struct ata_disk *);
static bool wait_while_busy (const struct ata_disk *);
static void select_device (const struct ata_disk *);
static void select_device_wait (const struct ata_disk *);

static void interrupt_handler (struct intr_frame *);

/* Initialize the disk subsystem and detect disks. */
void
ide_init (void)
{
size_t chan_no;

for (chan_no = 0; chan_no < CHANNEL_CNT; chan_no++){struct channel *c = &channels[chan_no];int dev_no;/* Initialize channel. */snprintf (c->name, sizeof c->name, ide%zu, chan_no);
switch (chan_no)
{
case 0:
c->reg_base = 0x1f0;
c->irq = 14 + 0x20;
break;
case 1:
c->reg_base = 0x170;
c->irq = 15 + 0x20;
break;
default:
NOT_REACHED ();
}
lock_init (&c->lock);
c->expecting_interrupt = false;
semaphore_init (&c->completion_wait, 0);

/* Initialize devices. */
for (dev_no = 0; dev_no < 2; dev_no++){struct ata_disk *d = &c->devices[dev_no];
snprintf (d->name, sizeof d->name,
hd%c, a + chan_no * 2 + dev_no);
d->channel = c;
d->dev_no = dev_no;
d->is_ata = false;
}

/* Register interrupt handler. */
intr_register_ext (c->irq, interrupt_handler, c->name);

/* Reset hardware. */
reset_channel (c);

/* Distinguish ATA hard disks from other devices. */
if (check_device_type (&c->devices[0]))
check_device_type (&c->devices[1]);

/* Read hard disk identity information. */
for (dev_no = 0; dev_no < 2; dev_no++)if (c->devices[dev_no].is_ata)
identify_ata_device (&c->devices[dev_no]);
}
}

/* Disk detection and identification. */

static char *descramble_ata_string (char *, int size);

/* Resets an ATA channel and waits for any devices present on it
to finish the reset. */
static void
reset_channel (struct channel *c)
{
bool present[2];
int dev_no;

/* The ATA reset sequence depends on which devices are present,
so we start by detecting device presence. */
for (dev_no = 0; dev_no < 2; dev_no++){struct ata_disk *d = &c->devices[dev_no];

select_device (d);

outb (reg_nsect (c), 0x55);
outb (reg_lbal (c), 0xaa);

outb (reg_nsect (c), 0xaa);
outb (reg_lbal (c), 0x55);

outb (reg_nsect (c), 0x55);
outb (reg_lbal (c), 0xaa);

present[dev_no] = (inb (reg_nsect (c)) == 0x55
&& inb (reg_lbal (c)) == 0xaa);
}

/* Issue soft reset sequence, which selects device 0 as a side effect.
Also enable interrupts. */
outb (reg_ctl (c), 0);
timer_usleep (10);
outb (reg_ctl (c), CTL_SRST);
timer_usleep (10);
outb (reg_ctl (c), 0);

timer_msleep (150);

/* Wait for device 0 to clear BSY. */
if (present[0])
{
select_device (&c->devices[0]);
wait_while_busy (&c->devices[0]);
}

/* Wait for device 1 to clear BSY. */
if (present[1])
{
int i;

select_device (&c->devices[1]);
for (i = 0; i < 3000; i++) {if (inb (reg_nsect (c)) == 1 && inb (reg_lbal (c)) == 1)break;timer_msleep (10);}wait_while_busy (&c->devices[1]);
}
}

/* Checks whether device D is an ATA disk and sets Ds is_ata
member appropriately.If D is device 0 (master), returns true
if its possible that a slave (device 1) exists on this
channel.If D is device 1 (slave), the return value is not
meaningful. */
static bool
check_device_type (struct ata_disk *d)
{
struct channel *c = d->channel;
uint8_t error, lbam, lbah, status;

select_device (d);

error = inb (reg_error (c));
lbam = inb (reg_lbam (c));
lbah = inb (reg_lbah (c));
status = inb (reg_status (c));

if ((error != 1 && (error != 0x81 || d->dev_no == 1))
|| (status & STA_DRDY) == 0
|| (status & STA_BSY) != 0)
{
d->is_ata = false;
return error != 0x81;
}
else
{
d->is_ata = (lbam == 0 && lbah == 0) || (lbam == 0x3c && lbah == 0xc3);
return true;
}
}

/* Sends an IDENTIFY DEVICE command to disk D and reads the
response.Registers the disk with the block device
layer. */
static void
identify_ata_device (struct ata_disk *d)
{
struct channel *c = d->channel;
char id[BLOCK_SECTOR_SIZE];
block_sector_t capacity;
char *model, *serial;
char extra_info[128];
struct block *block;

ASSERT (d->is_ata);

/* Send the IDENTIFY DEVICE command, wait for an interrupt
indicating the devices response is ready, and read the data
into our buffer. */
select_device_wait (d);
issue_pio_command (c, CMD_IDENTIFY_DEVICE);
semaphore_down (&c->completion_wait);
if (!wait_while_busy (d))
{
d->is_ata = false;
return;
}
input_sector (c, id);

/* Calculate capacity.
Read model name and serial number. */
capacity = *(uint32_t *) &id[60 * 2];
model = descramble_ata_string (&id[10 * 2], 20);
serial = descramble_ata_string (&id[27 * 2], 40);
snprintf (extra_info, sizeof extra_info,
model %s, serial %s, model, serial);

/* Disable access to IDE disks over 1 GB, which are likely
physical IDE disks rather than virtual ones.If we dont
allow access to those, were less likely to scribble on
someones important data.You can disable this check by
hand if you really want to do so. */
if (capacity >= 1024 * 1024 * 1024 / BLOCK_SECTOR_SIZE)
{
printf (%s: ignoring , d->name);
print_human_readable_size (capacity * 512);
printf (disk for safety
);
d->is_ata = false;
return;
}

/* Register. */
block = block_register (d->name, BLOCK_RAW, extra_info, capacity,
&ide_operations, d);
partition_scan (block);
}

/* Translates STRING, which consists of SIZE bytes in a funky
format, into a null-terminated string in-place.Drops
trailing whitespace and null bytes.Returns STRING.*/
static char *
descramble_ata_string (char *string, int size)
{
int i;

/* Swap all pairs of bytes. */
for (i = 0; i + 1 < size; i += 2){char tmp = string[i];string[i] = string[i + 1];string[i + 1] = tmp;}/* Find the last non-white, non-null character. */for (size–; size > 0; size)
{
int c = string[size 1];
if (c != && !isspace (c))
break;
}
string[size] = ;

return string;
}

/* Reads sector SEC_NO from disk D into BUFFER, which must have
room for BLOCK_SECTOR_SIZE bytes.
Internally synchronizes accesses to disks, so external
per-disk locking is unneeded. */
static void
ide_read (void *d_, block_sector_t sec_no, void *buffer)
{
struct ata_disk *d = d_;
struct channel *c = d->channel;
lock_acquire (&c->lock);
select_sector (d, sec_no);
issue_pio_command (c, CMD_READ_SECTOR_RETRY);
semaphore_down (&c->completion_wait);
if (!wait_while_busy (d))
PANIC (%s: disk read failed, sector=%PRDSNu, d->name, sec_no);
input_sector (c, buffer);
lock_release (&c->lock);
}

/* Write sector SEC_NO to disk D from BUFFER, which must contain
BLOCK_SECTOR_SIZE bytes.Returns after the disk has
acknowledged receiving the data.
Internally synchronizes accesses to disks, so external
per-disk locking is unneeded. */
static void
ide_write (void *d_, block_sector_t sec_no, const void *buffer)
{
struct ata_disk *d = d_;
struct channel *c = d->channel;
lock_acquire (&c->lock);
select_sector (d, sec_no);
issue_pio_command (c, CMD_WRITE_SECTOR_RETRY);
if (!wait_while_busy (d))
PANIC (%s: disk write failed, sector=%PRDSNu, d->name, sec_no);
output_sector (c, buffer);
semaphore_down (&c->completion_wait);
lock_release (&c->lock);
}

static struct block_operations ide_operations =
{
ide_read,
ide_write
};

/* Selects device D, waiting for it to become ready, and then
writes SEC_NO to the disks sector selection registers.(We
use LBA mode.) */
static void
select_sector (struct ata_disk *d, block_sector_t sec_no)
{
struct channel *c = d->channel;

ASSERT (sec_no < (1UL << 28));select_device_wait (d);outb (reg_nsect (c), 1);outb (reg_lbal (c), sec_no);outb (reg_lbam (c), sec_no >> 8);
outb (reg_lbah (c), (sec_no >> 16));
outb (reg_device (c),
DEV_MBS | DEV_LBA | (d->dev_no == 1 ? DEV_DEV : 0) | (sec_no >> 24));
}

/* Writes COMMAND to channel C and prepares for receiving a
completion interrupt. */
static void
issue_pio_command (struct channel *c, uint8_t command)
{
/* Interrupts must be enabled or our semaphore will never be
upd by the completion handler. */
ASSERT (intr_get_level () == INTR_ON);

c->expecting_interrupt = true;
outb (reg_command (c), command);
}

/* Reads a sector from channel Cs data register in PIO mode into
SECTOR, which must have room for BLOCK_SECTOR_SIZE bytes. */
static void
input_sector (struct channel *c, void *sector)
{
insw (reg_data (c), sector, BLOCK_SECTOR_SIZE / 2);
}

/* Writes SECTOR to channel Cs data register in PIO mode.
SECTOR must contain BLOCK_SECTOR_SIZE bytes. */
static void
output_sector (struct channel *c, const void *sector)
{
outsw (reg_data (c), sector, BLOCK_SECTOR_SIZE / 2);
}

/* Low-level ATA primitives. */

/* Wait up to 10 seconds for the controller to become idle, that
is, for the BSY and DRQ bits to clear in the status register.

As a side effect, reading the status register clears any
pending interrupt. */
static void
wait_until_idle (const struct ata_disk *d)
{
int i;

for (i = 0; i < 1000; i++) {if ((inb (reg_status (d->channel)) & (STA_BSY | STA_DRQ)) == 0)
return;
timer_usleep (10);
}

printf (%s: idle timeout
, d->name);
}

/* Wait up to 30 seconds for disk D to clear BSY,
and then return the status of the DRQ bit.
The ATA standards say that a disk may take as long as that to
complete its reset. */
static bool
wait_while_busy (const struct ata_disk *d)
{
struct channel *c = d->channel;
int i;

for (i = 0; i < 3000; i++){if (i == 700)printf (“%s: busy, waiting…”, d->name);
if (!(inb (reg_alt_status (c)) & STA_BSY))
{
if (i >= 700)
printf (ok
);
return (inb (reg_alt_status (c)) & STA_DRQ) != 0;
}
timer_msleep (10);
}

printf (failed
);
return false;
}

/* Program Ds channel so that D is now the selected disk. */
static void
select_device (const struct ata_disk *d)
{
struct channel *c = d->channel;
uint8_t dev = DEV_MBS;
if (d->dev_no == 1)
dev |= DEV_DEV;
outb (reg_device (c), dev);
inb (reg_alt_status (c));
timer_nsleep (400);
}

/* Select disk D in its channel, as select_device(), but wait for
the channel to become idle before and after. */
static void
select_device_wait (const struct ata_disk *d)
{
wait_until_idle (d);
select_device (d);
wait_until_idle (d);
}

/* ATA interrupt handler. */
static void
interrupt_handler (struct intr_frame *f)
{
struct channel *c;

for (c = channels; c < channels + CHANNEL_CNT; c++)if (f->vec_no == c->irq)
{
if (c->expecting_interrupt)
{
inb (reg_status (c)); /* Acknowledge interrupt. */
semaphore_up (&c->completion_wait);/* Wake up waiter. */
}
else
printf (%s: unexpected interrupt
, c->name);
return;
}

NOT_REACHED ();
}