[SOLVED] Java CSI3131 Lab3

CSI3131 Lab3
Objectives Thread Synchronization (Java)
To gain experience with Java semaphores in creating a simulation of a ferry that services automobiles and an ambulance. Read the lab document carefully before starting.
The Ferry
The ferry offers services between two ports, port 0 and port 1. Automobiles travel between these two ports, as well as ambulance(s). Each automobile arrives at a port, boards the ferry (when it arrives at the port), crosses to the other port, disembarks the ferry, travels around for a bit, and then goes back to the port to cross again.
The ambulance is a vehicle (the automobiles and ambulance are both vehicles) that functions like the automobilewiththeexception: whenanambulanceboardstheferry,theferryleavesimmediately without waiting to be full.
The ferry travels between the two ports (0 and 1): when it arrives at a port, vehicles on board disembark first, then any waiting vehicles board. When the ferry is full, or an ambulance boards, it leaves for the other port.
The provided java code Lab4.java contains 5 classes as follows:
Class FerryApp is a console application that create the Ferry and all automobiles in the
simulation
Class Auto simulates a single automobile thread
Class Ambulance simulates a single ambulance thread
Class Ferry simulates the ferry thread
Interface Logger that is used to assert correct operation of the ferry
To compile and run the simulation:
javac *.java
java FerryApp, or java -ea FerryApp
o (eaorEnableAssertionisusedtoasserttheproperoperationoftheferry,withthis flag enable the application will generate exceptions when an error is detected. Use this flag before submitting your lab to make sure your solution works fine)
You may pipe the output to a file for further analysis as follows (Linux only?!): java FerryApp | tee tmp.txt

Notes
Notice when you run the simulation there are going to be a lot of violations due to thread synchronization errors! Your task is to add the proper thread synchronization constructs to obey all the rules of the ferry simulation and have no errors as a result.
Your simulation must meet the following Rules:
1.The maximum capacity of the ferry is 5 vehicles. 2. A vehicle at port p boards the ferry if
a. The ferry is at the same port p,
b. All vehicles that arrived with the ferry on board have all disembarked the ferry, and c. Therestillexistsroomontheferryforthevehicle.
3.A vehicle at port p must wait
a. Iftheferryisnotatthesameportp, b. Vehicles are disembarking from the ferry, c. The ferry is full and is ready to leave.
4. If an ambulance boards the ferry, the ferry leaves immediately.
5. If the ferry is not full and with no ambulance on board, it waits for other automobiles to arrive. 6. A vehicle can disembark only at the arrival at the next port.
The above rules are checked in the code, you must leave all checks as is. The checks are going to be used to verify your solution.

Your Task
Your task is to modify the Auto, Ambulance, and Ferry classes by adding semaphore constructs to the Ferry class that will make the ferry simulation pass all the ferry rules without any error.
Guidelines
You can use the following guidelines:
The single Ferry object is visible in all other threads, thus it is an ideal candidate to hold all the
required semaphores for simulation
The addLoad, reduceLoad, loadAmbulance, unloadAmbulance methods should be mutually
exclusive. You can use the intrinsic locks for that see the lecture slides about intrinsic locks
The Ferry needs 2 semaphores, namely loadingDone, unloadingDone, to wait for vehicles to
be loaded before starting a crossing, and then waiting for vehicles to unload before allowing
vehicles to load
Vehicles (Auto, Ambulance) needs loadingSemaphore and unloadingSemaphore on each port
(i.e. array of 2 each) to synchronize the loading/unloading of vehicles on each port
When you provide a handle for InterruptedException, use the following code snip-it to let the
application terminate gracefully:
try {
////// your code here ///////
} catch (InterruptedException ie) { Thread.currentThread().interrupt(); System.out.println(Thread terminated by interruption); // handle the interrupt
return; }

When the Ferry is docking on port0 the situation looks like the following:
First the ferry signals the loading on port0, then waits for loading done, makes the crossing and then signals the unloading on port1, followed by a wait for unloading done. This finishes one loop of the ferry crossing.
Meanwhile, the vehicles on both sides are waiting to load on that port, then waits to unload on the opposite port after the ferry completes the crossing. The difference between the Ambulance and Auto is that the ambulance makes sure no other Auto is allowed to board after it by draining the permits (see Java Semaphore drainPermits) of the loading semaphore after entering it.
What is left is the events to signal the loadingDone, and unloadingDone semaphores, which can be easily detected in the addLoad, reduceLoad, loadAmbulance, unloadAmbulance methods of the ferry.

When the Ferry is docking on port1 the situation looks like the following:
Submission Note
Your code must compile & run to get the full mark. Were going to use other scenarios (number of crossings, autos, ambulances) to verify your solution. A bug free solution will support any scenario.