Computer Architecture Project 1 MIPS Disassembler
10% of Course Grade, Due: in three weeks (Oct. 1); 10% off each week late; Not accepted after Oct. 15.
Keep your source code. It may be used later in project three.
email addresses to send it : [email protected] AND [email protected] Please put CS472in the subject line to avoid it getting overlooked! ********************************************************************** * SHARE IDEAS, BUT NOT CODE. NOT ONE LINE! BASING YOUR WORK ON * * SOMEONE ELSES WILL GET YOU AN F FOR THE COURSE. DONT USE *
* OTHERS WORK TO GET AN IDEA OF HOW TO DO IT OR FOR ANY OTHER *
* REASON. NO EXCUSES. NO EXCEPTIONS. NO POSTING SOLUTIONS, EVER! * **********************************************************************
THE BASICS
Your project is to write a partial disassembler for MIPS instructions. That is, your input will be the 32-bit machine instructions that a compiler or assembler produces. Your program then figures out what the original source instructions were that created those 32-bit machine instructions and outputs them. The possible source instructions that you must be able to disassemble are: add, sub, and, or, slt, lw, sw, beq, bne. Ignore all other MIPS instructions.
The specific machine instructions that you will disassemble (one after another in this exact order) are: 0x032BA020, 0x8CE90014, 0x12A90003, 0x022DA822, 0xADB30020, 0x02697824, 0xAE8FFFF4, 0x018C6020, 0x02A4A825, 0x158FFFF7, 0x8ECDFFF0
That is, the above 32-bit instructions will be the input to your program. (Eight hex digits are 32 binary bits.) Feel free to embed them in the program itself so you can avoid typing them in each time. Your program will then analyze a 32-bit instruction and figure out what the opcode, register operands and other fields in the instruction are and then print out the assembly language instruction that produced it. Assume that the first instruction begins at address hex 9A040 and the rest follow right after that one. You must output the address along with the instruction.
For example, if your program determines that the first 32-bit machine instruction above is the instruction lw $10, 12 ($20) (it isnt, but if it were) then your output for that instruction would be:
9A040 lw $10, 12 ($20)
Youll then go on and do the next 32-bit instruction, specifying its address in hex (the address for an instruction immediately following one at 9A040) and what instruction caused those 32-bits. The instruction should show the correct syntax so that an assembler could correctly evaluate it (with the exception of the branch instruction detailed below). Output the numerical registers (e.g., $7, $0) as opposed to the symbolic descriptions (e.g., $s3, $t1
Show addresses in hex. All other values should be in decimal, which is what an assembler defaults to. For any load or store instructions, show the offset value as a signed decimal number.
The shamt field in R-type instructions can always be assumed to be all zeroes.
BRANCHES
For the branch instructions (beq, bne), dont try to invent a label for the destination to branch to. Just indicate the address of the destination. So if youve disassembled a beq $7, $8 instruction at 9A05C that is branching to an instruction at address 9A080, then your output should be:
9A05C beq $7, $8, address 9A080
You do not need to worry about branches that are an absurd distance away, which could cause problems with the short approach I suggested above.
BITWISE ANDS and SHIFTS
The key to this project is using bitwise AND operations and logical (not arithmetic) shifts. This is mandatory! A bitwise AND operation can be used to zero out all but some desired bits. A shift can get those bits into the desired position. In case you havent used these operations before, heres an example in C/C++. If the least significant bit is called bit 0 and the most significant bit is 31 and you want to look just at bits 7-10, you would do the following:
Bits_7_to_10 = All_32_bits & 0x00000780;
The bitwise AND (the & operation) does a bit-by-bit AND between the value in All_32_bits and the constant (known as a mask) hex 00000780. Hex 00000780 in binary is 0000 0000 0000 0000 0000 0111 1000 0000, which is zeros in all bits except bits 7, 8, 9, and 10. Any bit ANDed with a 0 is turned into 0, while any bit ANDed with a 1 is left as it is (1 AND 1 yields 1 while 0 AND 1 yields 0).
If you then wanted to take bits 7-10 and get them into the least significant position, you could shift by seven bits. Note: in java, use >>> not >>; in C++ used unsigned datatypes except the offset. This way you get a logical shift, not an arithmetic shift (which would give you unwanted leading 1s.)
Shifted_bits_7_to_10 = Bits_7_to_10 >> 7;
So if All_32_bits was hex F2C7AE82 (binary 1111 0010 1100 0111 1010 1110 1000 0010), then Bits_7_to_10 would be hex 00000680 (binary 0000 0000 0000 0000 0000 0110 1000 0000) and Shifted_bits_7_to_10 would be hex 0000000D (binary 0000 0000 0000 0000 0000 0000 0000 1101).
DONT CONVERT HEX NUMBERS TO DECIMAL OR STRINGS Do not use strings. Doing so will be much more work and hide that these are numbers. Also, you dont have to convert from hex to decimal or binary. The computer is always using binary and your languages I/O libraries handle displaying the binary number in its equivalent decimal or hex form. For example, hex 0x1C and binary 00011100 and decimal 28 are the exact same number. If you had three different variables and assigned them as follows:
int var1, var2, var3;
var1 = 28;
var2 = 0x1c;
var3 = 0b00011100; //binary constants not avail in all languages
If you now did a comparison of, or printed out, those variables, they would be exactly the same. The same holds true for signed numbers. If you have a signed integer that is -1, the internal twos complement representation is 0xFFFF FFFF or all binary 1s, but it prints out as -1. No conversion is necessary. The I/O libraries handle it all.
Taking another example, if youve set up an int for your first instruction (youll actually want to use an array of instructions, but I want to keep this simple) like this: int FirstInstruction = 00x022DA822;
Then for C++ you can do: cout << “The instruction shown in hex is: ” << hex << FirstInstruction;For java: System.out.println(“The instruction shown in hex is: ” + Integer.toHexString((firstinstruction)));SUGGESTIONSI suggest using a 16-bit variable (a short) for the I-format offset so that if the number is negative, it will be accurately handled. For example, if you take the number -4, it is represented in the 16-bit offset as xFFFC. When you do the bit-wise AND on the 32-bit instruction to remove the other 16 bits, youll correctly get xFFFC if you put it in a short but incorrectly get x0000FFFC if you put it in an int. If you print out the former for a load/store, youll correctly show -4, but if you print out the latter youll get a large positive number (64K-4), which is an error. This makes it so you don’t have to do sign-extension.
Reviews
There are no reviews yet.